Safety Data Sheet

SAFETY DATA SHEET

Date Accessed: 12/26/2024
Date Revised: 01/15/2022

SECTION 1. IDENTIFICATION

Product Name: Molybdenum Nanoparticles

Product Number: All applicable American Elements product codes, e.g. MO-M-03-NP , MO-M-04-NP , MO-M-05-NP , MO-M-02-NP

CAS #: 7439-98-7

Relevant identified uses of the substance: Scientific research and development

Supplier details:
American Elements
10884 Weyburn Ave.
Los Angeles, CA 90024
Tel: +1 310-208-0551
Fax: +1 310-208-0351

Emergency telephone number:
Domestic, North America: +1 800-424-9300
International: +1 703-527-3887


SECTION 2. HAZARDS IDENTIFICATION

Classification of the substance or mixture in accordance with 29 CFR 1910 (OSHA HCS)
GHS02 Flame
Flam. Sol. 2 H228 Flammable solid.
Hazards not otherwise classified
No data available.
GHS label elements
The product is classified and labeled in accordance with 29 CFR 1910 (OSHA HCS)
Hazard pictogram

Flame - GHS02

GHS02
Signal word
Warning
Hazard statements
H228 Flammable solid.
Precautionary statements
P210 Keep away from heat/sparks/open flames/hot surfaces. No smoking.
P280 Wear protective gloves/protective clothing/eye protection/face protection.
P240 Ground/bond container and receiving equipment.
P241 Use explosion-proof electrical/ventilating/lighting/equipment.
P370+P378 In case of fire: Use for extinction: CO2, powder or water spray.
WHMIS classification
B4 - Flammable solid
Classification system
HMIS ratings (scale 0-4)
(Hazardous Materials Identification System)
HEALTH
FIRE
REACTIVITY
1
2
1
Health (acute effects) = 1
Flammability = 2
Physical Hazard = 1
Other hazards
Results of PBT and vPvB assessment:
PBT:
N/A.
vPvB:
N/A.


SECTION 3. COMPOSITION/INFORMATION ON INGREDIENTS

Substances
CAS No. / Substance Name:
7439-98-7 Molybdenum
Identification number(s):
EC number:
231-107-2


SECTION 4. FIRST AID MEASURES

Description of first aid measures
If inhaled:
Supply fresh air. If not breathing, provide artificial respiration. Keep patient warm.
Seek immediate medical advice.
In case of skin contact:
Immediately wash with soap and water; rinse thoroughly.
Seek immediate medical advice.
In case of eye contact:
Rinse opened eye for several minutes under running water. Consult a physician.
If swallowed:
Seek medical treatment.
Information for doctor
Most important symptoms and effects, both acute and delayed
No information available.
Indication of any immediate medical attention and special treatment needed
No information available.


SECTION 5. FIREFIGHTING MEASURES

Extinguishing media
Suitable extinguishing media
Special powder for metal fires. Do not use water.
For safety reasons unsuitable extinguishing media
Water
Special hazards arising from the substance or mixture
If this product is involved in a fire, the following can be released:
Molybdenum oxides
Advice for firefighters
Protective equipment:
Wear self-contained respirator.
Wear fully protective impervious suit.


SECTION 6. ACCIDENTAL RELEASE MEASURES

Personal precautions, protective equipment and emergency procedures
Wear protective equipment. Keep unprotected persons away.
Ensure adequate ventilation
Keep away from ignition sources
Environmental precautions:
Do not allow material to be released to the environment without official permits.
Methods and material for containment and cleanup:
Keep away from ignition sources.
Ensure adequate ventilation.
Prevention of secondary hazards:
Keep away from ignition sources.
Reference to other sections
See Section 7 for information on safe handling
See Section 8 for information on personal protection equipment.
See Section 13 for disposal information.


SECTION 7. HANDLING AND STORAGE

Handling
Precautions for safe handling
Keep container tightly sealed.
Store in cool, dry place in tightly closed containers.
Ensure adequate ventilation.
Information about protection against explosions and fires:
Protect against electrostatic charges.
Conditions for safe storage, including any incompatibilities
Storage
Requirements to be met by storerooms and receptacles:
Store in a cool location.
Information about storage in one common storage facility:
Store away from oxidizing agents.
Do not store together with acids.
Further information about storage conditions:
Keep container tightly sealed.
Store in cool, dry conditions in well-sealed containers.
Specific end use(s)
No information available.


SECTION 8. EXPOSURE CONTROLS/PERSONAL PROTECTION

Additional information about design of technical systems:
Properly operating chemical fume hood designed for hazardous chemicals and having an average face velocity of at least 100 feet per minute.
Control parameters
Components with limit values that require monitoring at the workplace:
7439-98-7 Molybdenum (100.0%)
PEL (USA) Long-term value: 5* 15** mg/m³
as Mo;*soluble compds.,
**insol.compds.:total dust
TLV (USA) Long-term value: 10* 3** mg/m³
as Mo; *inhalable fraction ** respirable fraction
EL (Canada) Long-term value: 3* 10** mg/m³
as Mo; *respirable **inhalable
EV (Canada) Long-term value: 10* 3** 0.5*** mg/m³
metal,insol.compd.:*inh;**resp;sol.compd.:***resp
Additional information:
No data
Exposure controls
Personal protective equipment
Follow typical general protective and industrial hygiene measures for handling chemicals.
Keep away from foodstuffs, beverages and feed.
Remove all soiled and contaminated clothing immediately.
Wash hands before breaks and at the end of work.
Breathing equipment:
Use suitable respirator when high concentrations are present.
Recommended filter device for short term use:
Use a respirator with type N95 (USA) or PE (EN 143) cartridges as a backup to engineering controls. Risk assessment should be performed to determine if air-purifying respirators are appropriate. Only use equipment tested and approved under appropriate government standards.
Protection of hands:
Impervious gloves
Inspect gloves prior to use.
The selection of suitable gloves not only
depends on the material, but also on quality. Quality will vary from manufacturer to manufacturer.
Material of gloves
Nitrile rubber, NBR
Penetration time of glove material (in minutes)
480
Glove thickness
0.11 mm
Eye protection:
Safety glasses
Body protection:
Protective work clothing


SECTION 9. PHYSICAL AND CHEMICAL PROPERTIES

Information on basic physical and chemical properties
Appearance:
Form:
Powder
Color:
gray
Odor:
Odorless
Odor threshold:
No data available.
pH:
N/A.
Melting point/range:
2623 °C (4753 °F)
Boiling point/range:
4639 °C (8382 °F)
Sublimation temperature / start:
No data available.
Flammability (solid, gas):
Highly flammable.
Ignition temperature:
No data available.
Decomposition temperature:
No data available.
Auto igniting:
No data available.
Danger of explosion:
No data available.
Explosion limits:
Lower:
No data available.
Upper:
No data available.
Vapor pressure:
N/A.
Density at 20 °C (68 °F):
10.22 g/cm³ (85.286 lbs/gal)
Relative density
No data available.
Vapor density
N/A.
Evaporation rate
N/A.
Solubility in / Miscibility with
Water:
No data available.
Partition coefficient (n-octanol/water):
No data available.
Viscosity:
Dynamic:
N/A.
Kinematic:
N/A.
Other information
No information available.


SECTION 10. STABILITY AND REACTIVITY

Reactivity
No data available.
Chemical stability
Stable under recommended storage conditions.
Thermal decomposition / conditions to be avoided:
Decomposition will not occur if used and stored according to specifications.
Possibility of hazardous reactions
No dangerous reactions known
Conditions to avoid
No information available.
Incompatible materials:
Acids
Oxidizing agents
Hazardous decomposition products:
Molybdenum oxides


SECTION 11. TOXICOLOGICAL INFORMATION

Information on toxicological effects
Acute toxicity:
The Registry of Toxic Effects of Chemical Substances (RTECS) contains acute toxicity data for this substance.
LD/LC50 values that are relevant for classification:
No data
Skin irritation or corrosion:
May cause irritation
Eye irritation or corrosion:
May cause irritation
Sensitization:
No sensitizing effects known.
Germ cell mutagenicity:
The Registry of Toxic Effects of Chemical Substances (RTECS) contains mutation data for this substance.
Carcinogenicity:
No classification data on carcinogenic properties of this material is available from the EPA, IARC, NTP, OSHA or ACGIH.
Reproductive toxicity:
The Registry of Toxic Effects of Chemical Substances
(RTECS) contains reproductive data for this substance.
Specific target organ system toxicity - repeated exposure:
N/A
Specific target organ system toxicity - single exposure:
N/A
Aspiration hazard:
N/A
Subacute to chronic toxicity:
The Registry of Toxic Effects of Chemical Substances (RTECS) contains multiple dose toxicity data for this substance.
Additional toxicological information:
To the best of our knowledge the acute and chronic toxicity of this substance is not fully known


SECTION 12. ECOLOGICAL INFORMATION

Toxicity
Aquatic toxicity:
No information available.
Persistence and degradability:
No information available.
Bioaccumulative potential:
No information available.
Mobility in soil:
No information available.
Additional ecological information:
General notes:
Do not allow material to be released to the environment without official permits.
Do not allow undiluted product or large quantities to reach ground water, water course or sewage system.
Avoid transfer into the environment.
Results of PBT and vPvB assessment:
PBT:
N/A.
vPvB:
N/A.
Other adverse effects
No further relevant information available


SECTION 13. DISPOSAL CONSIDERATIONS

Waste treatment methods
Recommendation:
Consult state, local or national regulations to ensure proper disposal.
Uncleaned packagings:
Recommendation:
Disposal must be made according to official regulations


SECTION 14. TRANSPORT INFORMATION

UN-Number
DOT, IMDG, IATA
UN308


SECTION 15. REGULATORY INFORMATION

UN proper shipping name
DOT
Metal powders, flammable, n.o.s. (Molybdenum powder)
IMDG, IATA
METAL POWDER, FLAMMABLE, N.O.S. (Molybdenum powder)
Transport hazard class(es)
DOT
Class
4.1 Flammable solids, self-reactive substances and solid desensitised explosives.
Label
4.1
Class
4.1 (F3) Flammable solids, self-reactive substances and solid desensitised explosives
Label
4.1
IMDG, IATA
Class
4.1 Flammable solids, self-reactive substances and solid desensitised explosives.
Label
4.1
Packing group
DOT, IMDG, IATA
III
Environmental hazards:
N/A.
Special precautions for user
Warning: Flammable solids, self-reactive substances and solid desensitised explosives
EMS Number:
F-G,S-G
Segregation groups
Heavy metals and their salts (including their organometallic compounds), powdered metals
Transport in bulk according to Annex II of MARPOL73/78 and the IBC Code
N/A.
Transport/Additional information:
DOT
Marine Pollutant (DOT):
No
UN "Model Regulation":
UN3089, Metal powders, flammable, n.o.s. (Molybdenum powder), 4.1, III