Rhodium Sulfate Solution

CAS #:

Linear Formula:

Rh2(SO4)3 • 4H2O

MDL Number:

MFCD00016309

EC No.:

N/A

ORDER

PRODUCT Product Code ORDER SAFETY DATA TECHNICAL DATA
(2N) 99% Rhodium Sulfate Solution
RH-SAT-02-SOL
Pricing > SDS > Data Sheet >
(3N) 99.9% Rhodium Sulfate Solution
RH-SAT-03-SOL
Pricing > SDS > Data Sheet >

Rhodium Sulfate Solution Properties (Theoretical)

Compound Formula Rh2(SO4)3 • 4H2O
Molecular Weight 566.05
Appearance liquid
Melting Point N/A
Boiling Point N/A
Density 1.217 g/cm3
Solubility in H2O N/A
Exact Mass N/A
Monoisotopic Mass 493.666199 Da
Charge N/A

Rhodium Sulfate Solution Health & Safety Information

Signal Word N/A
Hazard Statements N/A
Hazard Codes N/A
Risk Codes N/A
Safety Statements N/A
Transport Information N/A
GHS Pictograms

View and Print SDS

SAFETY DATA SHEET

Date Accessed: 12/21/2024
Date Revised:01/15/2022

SECTION 1. IDENTIFICATION

Product Name: Rhodium Sulfate Solution

Product Number: All applicable American Elements product codes, e.g. RH-SAT-02-SOL , RH-SAT-03-SOL

CAS #: 10489-46-0

Relevant identified uses of the substance: Scientific research and development

Supplier details:
American Elements
10884 Weyburn Ave.
Los Angeles, CA 90024
Tel: +1 310-208-0551
Fax: +1 310-208-0351

Emergency telephone number:
Domestic, North America: +1 800-424-9300
International: +1 703-527-3887


SECTION 2. HAZARDS IDENTIFICATION

Classification of the substance or mixture in accordance with 29 CFR 1910 (OSHA HCS)
GHS05 Corrosion
Skin Corr. 1A H314 Causes severe skin burns and eye damage.
Hazards not otherwise classified No data available.
GHS label elements The product is classified and labeled in accordance with 29 CFR 1910 (OSHA HCS)

Corrosion - GHS05

Hazard pictograms
GHS05
Signal word Danger
Hazard-determining components of labeling:
Sulfuric acid
Rhodium(III) sulfate
Hazard statements
H314 Causes severe skin burns and eye damage.
Precautionary statements
P260 Do not breathe dust/fume/gas/mist/vapors/spray.
P303+P361+P353 If on skin (or hair): Take off immediately all contaminated clothing. Rinse skin with water/shower.
P305+P351+P338 IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy

to do. Continue rinsing.
P301+P330+P331 IF SWALLOWED: rinse mouth. Do NOT induce vomiting.
P405 Store locked up.
P501 Dispose of contents/container in accordance with local/regional/national/international regulations.
WHMIS classification
D2B - Toxic material causing other toxic effects
E - Corrosive material
Classification system
HMIS ratings (scale 0-4)
(Hazardous Materials Identification System)
HEALTH
FIRE
REACTIVITY
3

1
Health (acute effects) = 3
Flammability = 0
Physical Hazard = 1
Other hazards
Results of PBT and vPvB assessment:
PBT: N/A.
vPvB: N/A.


SECTION 3. COMPOSITION/INFORMATION ON INGREDIENTS

Chemical characterization: Mixtures
Dangerous components:
7664-93-9 Sulfuric acid Skin Corr. 1A, H314 25.0%
10489-46-0 Rhodium(III) sulfate Met. Corr.1, H290; Skin Corr. 1B, H314; Eye Dam. 1, H318 12.0%
Additional information None known.
Non-Hazardous Ingredients
7732-18-5 Water


SECTION 4. FIRST AID MEASURES

Description of first aid measures
General information Immediately remove any clothing soiled by the product.
If inhaled:
Supply fresh air. If not breathing, provide artificial respiration. Keep patient warm.
Seek immediate medical advice.
In case of skin contact:
Immediately wash with soap and water; rinse thoroughly.
Seek immediate medical advice.
In case of eye contact: Rinse opened eye for several minutes under running water. Consult a physician.
If swallowed: Seek medical treatment.
Information for doctor
Most important symptoms and effects, both acute and delayed
Causes severe skin burns.
Causes serious eye damage.
Indication of any immediate medical attention and special treatment needed No information available.


SECTION 5. FIREFIGHTING MEASURES

Extinguishing media
Suitable extinguishing media Product is not flammable. Use fire-fighting measures that suit the surrounding fire.
Special hazards arising from the substance or mixture
If this product is involved in a fire, the following can be released:
Sulfur oxides (SOx)
Rhodium oxide
Advice for firefighters
Protective equipment:
Wear self-contained respirator.
Wear fully protective impervious suit.


SECTION 6. ACCIDENTAL RELEASE MEASURES

Personal precautions, protective equipment and emergency procedures
Wear protective equipment. Keep unprotected persons away.
Ensure adequate ventilation
Environmental precautions: Do not allow material to be released to the environment without official permits.
Methods and material for containment and cleanup:
Absorb with liquid-binding material (sand, diatomite, acid binders, universal binders, sawdust).
Use neutralizing agent.
Dispose of contaminated material as waste according to section 13.
Ensure adequate ventilation.
Prevention of secondary hazards: No special measures required.
Reference to other sections
See Section 7 for information on safe handling
See Section 8 for information on personal protection equipment.
See Section 13 for disposal information.


SECTION 7. HANDLING AND STORAGE

Handling
Precautions for safe handling
Keep container tightly sealed.
Store in cool, dry place in tightly closed containers.
Ensure adequate ventilation.
Information about protection against explosions and fires: The product is not flammable
Conditions for safe storage, including any incompatibilities
Storage
Requirements to be met by storerooms and receptacles: No special requirements.
Information about storage in one common storage facility:
Store away from strong bases.
Store away from oxidizing agents.
Store away from reducing agents.
Store away from metal powders.
Water reacts with many metals to give hydrogen, often violently. Water is also incompatible with many reactive organic

and inorganic chemicals.
Further information about storage conditions:
Keep container tightly sealed.
Store in cool, dry conditions in well-sealed containers.
Specific end use(s) No information available.


SECTION 8. EXPOSURE CONTROLS/PERSONAL PROTECTION

Additional information about design of technical systems:
Properly operating chemical fume hood designed for hazardous chemicals and having an average face velocity of at least

100 feet per minute.
Control parameters
Components with limit values that require monitoring at the workplace:
7664-93-9 Sulfuric acid (25.0%)
PEL (USA) Long-term value: 1 mg/m³
REL (USA) Long-term value: 1 mg/m³
TLV (USA) Long-term value: 0.2* mg/m³
*as thoracic fraction
EL (Canada) Long-term value: 0.2 mg/m³
ACGIH A2; IARC 1
EV (Canada) Long-term value: 0.2 mg/m³
10489-46-0 Rhodium(III) sulfate (12.0%)
TLV (USA) Long-term value: 0.01 mg/m³
as Rh
Additional information: No data
Exposure controls
Personal protective equipment
Follow typical general protective and industrial hygiene measures for handling chemicals.
Keep away from foodstuffs, beverages and feed.
Remove all soiled and contaminated clothing immediately.
Wash hands before breaks and at the end of work.
Do not inhale dust / smoke / mist.
Avoid contact with the eyes and skin.
Breathing equipment: Use suitable respirator when high concentrations are present.
Protection of hands:
Impervious gloves
Inspect gloves prior to use.
The selection of suitable gloves not only depends on the material, but also on quality. Quality will vary from

manufacturer to manufacturer.
Penetration time of glove material (in minutes) No data available.
Eye protection:
Tightly sealed goggles
Full face protection
Body protection: Protective work clothing.


SECTION 9. PHYSICAL AND CHEMICAL PROPERTIES

Information on basic physical and chemical properties
Appearance:
Form: Liquid
Color: Red-orange
Odor: Acidic
Odor threshold: No data available.
pH: No data available.
Melting point/range: No data available.
Boiling point/range: No data available.
Sublimation temperature / start: No data available.
Flammability (solid, gas): No data available.
Ignition temperature: No data available.
Decomposition temperature: No data available.
Auto igniting: Product is not selfigniting.
Danger of explosion: No data available.
Explosion limits:
Lower: No data available.
Upper: No data available.
Vapor pressure at 20 °C (68 °F): 23 hPa (17 mm Hg)
Density at 20 °C (68 °F): 1.4 g/cm³ (11.683 lbs/gal)
Relative density No data available.
Vapor density No data available.
Evaporation rate No data available.
Solubility in / Miscibility with
Water: Fully miscible
Partition coefficient (n-octanol/water): No data available.
Viscosity:
Dynamic: No data available.
Kinematic: No data available.
Solvent content:
Organic solvents: 0.0 %
Solids content: 12.0 %
Other information No information available.


SECTION 10. STABILITY AND REACTIVITY

Reactivity No data available.
Chemical stability Stable under recommended storage conditions.
Thermal decomposition / conditions to be avoided: Decomposition will not occur if used and stored according to

specifications.
Possibility of hazardous reactions
Water reacts violently with alkali metals.
Reacts with strong oxidizing agents
Water reacts with many metals to give hydrogen, often violently. Water is also incompatible with many reactive organic

and inorganic chemicals.
Conditions to avoid No information available.
Incompatible materials:
Bases
Oxidizing agents
Reducing agents
Metal powders
Hazardous decomposition products:
Sulfur oxides (SOx)
Rhodium oxide


SECTION 11. TOXICOLOGICAL INFORMATION

Information on toxicological effects
Acute toxicity:
Swallowing will lead to a strong corrosive effect on mouth and throat and to the danger of perforation of esophagus and

stomach.
The Registry of Toxic Effects of Chemical Substances (RTECS) contains acute toxicity data for components in this

product.
LD/LC50 values that are relevant for classification: No data
Skin irritation or corrosion: Causes severe skin burns.
Eye irritation or corrosion: Causes serious eye damage.
Sensitization: No sensitizing effects known.
Germ cell mutagenicity: The Registry of Toxic Effects of Chemical Substances (RTECS) contains mutation data for

components in this product.
Carcinogenicity:
ACGIH A4: Not classifiable as a human carcinogen: Inadequate data on which to classify the agent in terms of its

carcinogenicity in humans and/or animals.
Reproductive toxicity: The Registry of Toxic Effects of Chemical Substances (RTECS) contains reproductive data for

components in this product.
Specific target organ system toxicity - repeated exposure: N/A
Specific target organ system toxicity - single exposure: N/A
Aspiration hazard: N/A
Subacute to chronic toxicity: The Registry of Toxic Effects of Chemical Substances (RTECS) contains multiple dose

toxicity data for this substance.
Additional toxicological information:
To the best of our knowledge the acute and chronic toxicity of this substance is not fully known.
The product shows the following dangers according to internally approved calculation methods for preparations:
Corrosive


SECTION 12. ECOLOGICAL INFORMATION

Toxicity
Aquatic toxicity: No information available.
Persistence and degradability: No information available.
Bioaccumulative potential: No information available.
Mobility in soil: No information available.
Additional ecological information:
General notes:
Do not allow product to reach ground water, water course or sewage system.
Do not allow material to be released to the environment without official permits.
Danger to drinking water if even small quantities leak into the ground.
Avoid transfer into the environment.
Results of PBT and vPvB assessment:
PBT: N/A.
vPvB: N/A.
Other adverse effects No information available.


SECTION 13. DISPOSAL CONSIDERATIONS

Waste treatment methods
Recommendation: Consult state, local or national regulations to ensure proper disposal.
Uncleaned packagings:
Recommendation: Disposal must be made according to official regulations.
Recommended cleansing agent: Water, if necessary with cleansing agents.


SECTION 14. TRANSPORT INFORMATION

UN-Number
DOT, IMDG, IATA UN3264
UN proper shipping name
DOT Corrosive liquid, acidic, inorganic, n.o.s. (Rhodium(III) sulfate, Sulfuric acid)
IMDG, IATA CORROSIVE LIQUID, ACIDIC, INORGANIC, N.O.S. (Rhodium(III) sulfate,
SULPHURIC ACID)
Transport hazard class(es)
DOT
Class 8 Corrosive substances.
Label 8
Class 8 (C1) Corrosive substances
Label 8
IMDG, IATA
Class 8 Corrosive substances.
Label 8
Packing group
DOT, IMDG, IATA III
Environmental hazards:
Marine pollutant (IMDG): No
Special precautions for user Warning: Corrosive substances
EMS Number: F-A,S-B
Segregation groups Acids
Transport in bulk according to Annex II of MARPOL73/78 and the IBC Code N/A.
Transport/Additional information:
DOT
Marine Pollutant (DOT): No
UN "Model Regulation": UN3264, Corrosive liquid, acidic, inorganic, n.o.s. (Rhodium(III) sulfate, Sulfuric
acid), 8, III


SECTION 15. REGULATORY INFORMATION

Safety, health and environmental regulations/legislation specific for the substance or mixture
GHS label elements The product is classified and labeled in accordance with 29 CFR 1910 (OSHA HCS)
Hazard pictograms
GHS05
Signal word Danger
Hazard-determining components of labeling:
Sulfuric acid
Rhodium(III) sulfate
Hazard statements
H314 Causes severe skin burns and eye damage.
Precautionary statements
P260 Do not breathe dust/fume/gas/mist/vapors/spray.
P303+P361+P353 If on skin (or hair): Take off immediately all contaminated clothing. Rinse skin with water/shower.
P305+P351+P338 IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy

to do. Continue rinsing.
P301+P330+P331 IF SWALLOWED: rinse mouth. Do NOT induce vomiting.
P405 Store locked up.
P501 Dispose of contents/container in accordance with local/regional/national/international regulations.
National regulations
All components of this product are listed in the U.S. Environmental Protection Agency Toxic Substances Control Act

Chemical substance Inventory.
All components of this product are listed on the Canadian Domestic Substances List (DSL).
SARA Section 313 (specific toxic chemical listings)
7664-93-9 Sulfuric acid 25.0%
California Proposition 65
Prop 65 - Chemicals known to cause cancer
None of the ingredients are listed.
Prop 65 - Developmental toxicity
None of the ingredients are listed.
Prop 65 - Developmental toxicity, female
None of the ingredients are listed.
Prop 65 - Developmental toxicity, male
None of the ingredients are listed.
Information about limitation of use: For use only by technically qualified individuals.
Other regulations, limitations and prohibitive regulations
Substance of Very High Concern (SVHC) according to the REACH Regulations (EC) No. 1907/2006.
None of the ingredients are listed.
The conditions of restrictions according to Article 67 and Annex XVII of the Regulation (EC) No 1907/2006 (REACH) for

the manufacturing, placing on the
market and use must be observed.
None of the ingredients is listed.
Annex XIV of the REACH Regulations (requiring Authorisation for use)
None of the ingredients is listed.
Chemical safety assessment: A Chemical Safety Assessment has not been carried out.


SECTION 16. OTHER INFORMATION

Safety Data Sheet according to Regulation (EC) No. 1907/2006 (REACH). The above information is believed to be correct but does not purport to be all inclusive and shall be used only as a guide. The information in this document is based on the present state of our knowledge and is applicable to the product with regard to appropriate safety precautions. It does not represent any guarantee of the properties of the product. American Elements shall not be held liable for any damage resulting from handling or from contact with the above product. See reverse side of invoice or packing slip for additional terms and conditions of sale. COPYRIGHT 1997-2022 AMERICAN ELEMENTS. LICENSED GRANTED TO MAKE UNLIMITED PAPER COPIES FOR INTERNAL USE ONLY.

About Rhodium Sulfate Solution

Sulfate IonRhodium Sulfate Solutions are moderate to highly concentrated liquid solutions of Rhodium Sulfate. They are an excellent source of Rhodium Sulfate for applications requiring solubilized Compound Solutions Packaging, Bulk Quantity materials. American Elements can prepare dissolved homogeneous solutions at customer specified concentrations or to the maximum stoichiometric concentration. Packaging is available in 55 gallon drums, smaller units and larger liquid totes. American Elements maintains solution production facilities in the United States, Northern Europe (Liverpool, UK), Southern Europe (Milan, Italy), Australia and China to allow for lower freight costs and quicker delivery to our customers. American Elements metal and rare earth compound solutions have numerous applications, but are commonly used in petrochemical cracking and automotive catalysts, water treatment, plating, textiles, research and in optic, laser, crystal and glass applications. Ultra high purity and high purity compositions improve both optical quality and usefulness as scientific standards. Nanoscale elemental powders and suspensions, as alternative high surface area forms, may be considered. We also produce Rhodium Sulfate Powder. Sulfate compounds are salts or esters of sulfuric acid formed by replacing one or both of the hydrogens with a metal. Most metal sulfate compounds are readily soluble in water for uses such as water treatment, unlike fluorides and oxides which tend to be insoluble. Organometallic forms are soluble in organic solutions and sometimes in both aqueous and organic solutions. Metallic ions can also be dispersed utilizing suspended or coated nanoparticles and deposited utilizing sputtering targets and evaporation materials for uses such as solar cells and fuel cells. American Elements produces to many standard grades when applicable, including Mil Spec (military grade); ACS, Reagent and Technical Grade; Food, Agricultural and Pharmaceutical Grade; Optical Grade, USP and EP/BP (European Pharmacopoeia/British Pharmacopoeia) and follows applicable ASTM testing standards. Typical and custom packaging is available. Additional technical, research and safety (MSDS) information is available as is a Reference Calculator for converting relevant units of measurement.

Rhodium Sulfate Solution Synonyms

Rhodium(III) Sulfate, Rhodium; sulfuric acid

Chemical Identifiers

Linear Formula Rh2(SO4)3 • 4H2O
MDL Number MFCD00016309
EC No. N/A
Beilstein/Reaxys No. N/A
Pubchem CID N/A
IUPAC Name Rhodium(3+) sulfate (2:3)
SMILES [Rh+3].[Rh+3].[O-]S(=O)(=O)[O-].[O-]S([O-])(=O)=O.[O-]S([O-])(=O)=O
InchI Identifier InChI=1S/3H2O 4S.2Rh/c3*1-5(2,3)4;;/h3* (H2,1,2,3,4);;/q;;;2*+3/p-6
InchI Key YWFDDXXMOPZFFM-UHFFFAOYSA-H

Packaging Specifications

Typical bulk packaging includes palletized plastic 5 gallon/25 kg. pails, fiber and steel drums to 1 ton super sacks in full container (FCL) or truck load (T/L) quantities. Research and sample quantities and hygroscopic, oxidizing or other air sensitive materials may be packaged under argon or vacuum. Shipping documentation includes a Certificate of Analysis and Safety Data Sheet (SDS). Solutions are packaged in polypropylene, plastic or glass jars up to palletized 440 gallon liquid totes, and 36,000 lb. tanker trucks.

Related Elements

Rhodium

See more Rhodium products. Rhodium (atomic symbol: Rh, atomic number: 45) is a Block D, Group 9, Period 5 element with an atomic weight of 102.90550. Rhodium Bohr ModelThe number of electrons in each of Rhodium's shells is [2, 8, 18, 16, 1] and its electron configuration is [Kr] 4d8 5s1. The rhodium atom has a radius of 134 pm and a Van der Waals radius of 195 pm. Rhodium was discovered and first isolated by William Wollaston in 1804. In its elemental form, rhodium has a silvery white metallic appearance. Elemental RhodiumRhodium is a member of the platinum group of metals. It has a higher melting point than platinum, but a lower density. Rhodium is found in ores mixed with other metals such as palladium, silver, platinum, and gold. Rhodium is primarily used as the catalyst in the three-way catalytic converters of automobiles it is also highly valued in jewelry. The name Rhodium originates from the Greek word 'Rhodon,' which means rose.

Sulfur

See more Sulfur products. Sulfur (or Sulphur) (atomic symbol: S, atomic number: 16) is a Block P, Group 16, Period 3 element with an atomic radius of 32.066. Sulfur Bohr ModelThe number of electrons in each of Sulfur's shells is 2, 8, 6 and its electron configuration is [Ne] 3s2 3p4. In its elemental form, sulfur has a light yellow appearance. The sulfur atom has a covalent radius of 105 pm and a Van der Waals radius of 180 pm. In nature, sulfur can be found in hot springs, meteorites, volcanoes, and as galena, gypsum, and epsom salts. Sulfur has been known since ancient times but was not accepted as an element until 1777, when Antoine Lavoisier helped to convince the scientific community that it was an element and not a compound.

TODAY'S TOP DISCOVERY!

December 21, 2024
Los Angeles, CA
Each business day American Elements' scientists & engineers post their choice for the most exciting materials science news of the day
Physics student builds improvised polarimeter using simple circuitry, polarizing film, and LEGO toy bricks

Physics student builds improvised polarimeter using simple circuitry, polarizing film, and LEGO toy bricks