Sulfur Nanoparticles / Nanopowder

CAS #:

Linear Formula:

S

MDL Number:

MFCD00085316

EC No.:

231-722-6

ORDER

PRODUCT Product Code ORDER SAFETY DATA TECHNICAL DATA
(2N) 99% Sulfur Nanopowder
S-E-02-NP
Pricing > SDS > Data Sheet >
(3N) 99.9% Sulfur Nanopowder
S-E-03-NP
Pricing > SDS > Data Sheet >
(4N) 99.99% Sulfur Nanopowder
S-E-04-NP
Pricing > SDS > Data Sheet >
(5N) 99.999% Sulfur Nanopowder
S-E-05-NP
Pricing > SDS > Data Sheet >

Sulfur Nanoparticles / Nanopowder Properties (Theoretical)

Molecular Weight 32.065
Appearance Pale yellow powder
Melting Point 115.21 °C
Boiling Point 444.6 °C
Density 1.9-2.1 g/cm3
Solubility in H2O Insoluble
Electrical Resistivity 0.205 W·m-1·K-1
Electronegativity 2.58 Paulings
Heat of Vaporization 45 kJ mol-1
Specific Heat N/A
Tensile Strength N/A
Thermal Conductivity 0.205 W/cm/K

Sulfur Nanoparticles / Nanopowder Health & Safety Information

Signal Word Danger
Hazard Statements H228-H315
Hazard Codes F
Precautionary Statements P210-P240-P241-P280-P321-P362
Flash Point 207 °C (closed cup)
Risk Codes N/A
Safety Statements N/A
RTECS Number WS4250000
Transport Information UN1350 4.1/PG III
WGK Germany 1
GHS Pictograms

View and Print SDS

SAFETY DATA SHEET

Date Accessed: 11/12/2024
Date Revised:01/15/2022

SECTION 1. IDENTIFICATION

Product Name: Sulfur Nanoparticles / Nanopowder

Product Number: All applicable American Elements product codes, e.g. S-E-02-NP , S-E-03-NP , S-E-04-NP , S-E-05-NP

CAS #: 7704-34-9

Relevant identified uses of the substance: Scientific research and development

Supplier details:
American Elements
10884 Weyburn Ave.
Los Angeles, CA 90024
Tel: +1 310-208-0551
Fax: +1 310-208-0351

Emergency telephone number:
Domestic, North America: +1 800-424-9300
International: +1 703-527-3887


SECTION 2. HAZARDS IDENTIFICATION

Classification of the substance or mixture in accordance with 29 CFR 1910 (OSHA HCS)
GHS02 Flame
Flam. Sol. 1 H228 Flammable solid.
GHS07
Skin Irrit. 2 H315 Causes skin irritation.
Hazards not otherwise classified
No data available.

Exclamation Mark - GHS07 Flame - GHS02

GHS label elements
The product is classified and labeled in accordance with 29 CFR 1910 (OSHA HCS)
Hazard pictograms
GHS02
GHS07
Signal word
Danger
Hazard statements
H228 Flammable solid.
H315 Causes skin irritation.
Precautionary statements
P210 Keep away from heat/sparks/open flames/hot surfaces. - No smoking.
P280 Wear protective gloves/protective clothing/eye protection/face protection.
P240 Ground/bond container and receiving equipment.
P241 Use explosion-proof electrical/ventilating/lighting/equipment.
P362 Take off contaminated clothing and wash before reuse.
P321 Specific treatment (see on this label).
WHMIS classification
B4 - Flammable solid
D2B - Toxic material causing other toxic effects
Classification system
HMIS ratings (scale 0-4)
(Hazardous Materials Identification System)
HEALTH 1
FIRE 2
REACTIVITY 0
Health (acute effects) = 1
Flammability = 2
Physical Hazard = 0
Other hazards
Results of PBT and vPvB assessment:
PBT:
N/A.
vPvB:
N/A.


SECTION 3. COMPOSITION/INFORMATION ON INGREDIENTS

Substances
CAS No. / Substance Name: 7704-34-9 Sulphur
Identification number(s):
EC number: 231-722-6
Index number: 016-094-00-1


SECTION 4. FIRST AID MEASURES

Description of first aid measures
If inhaled:
Supply fresh air. If not breathing, provide artificial respiration. Keep patient warm.
Seek immediate medical advice.
In case of skin contact:
Immediately wash with soap and water; rinse thoroughly.
Seek immediate medical advice.
In case of eye contact:
Rinse opened eye for several minutes under running water. Consult a physician.
If swallowed:
Seek medical treatment.
Information for doctor
Most important symptoms and effects, both acute and delayed
No information available.
Indication of any immediate medical attention and special treatment needed
No information available.


SECTION 5. FIREFIGHTING MEASURES

Extinguishing media
Suitable extinguishing media
Carbon dioxide, extinguishing powder or water spray. Fight larger fires with water spray or alcohol resistant foam.
Special hazards arising from the substance or mixture
If this product is involved in a fire, the following can be released:
Sulfur oxides (SOx)
Hydrogen sulfide
Advice for firefighters
Protective equipment:
Wear self-contained respirator.
Wear fully protective impervious suit.


SECTION 6. ACCIDENTAL RELEASE MEASURES

Personal precautions, protective equipment and emergency procedures
Wear protective equipment. Keep unprotected persons away.
Ensure adequate ventilation
Keep away from ignition sources
Environmental precautions:
Do not allow material to be released to the environment without official permits.
Methods and material for containment and cleanup:
Keep away from ignition sources.
Ensure adequate ventilation.
Prevention of secondary hazards:
Keep away from ignition sources.
Reference to other sections
See Section 7 for information on safe handling
See Section 8 for information on personal protection equipment.
See Section 13 for disposal information.


SECTION 7. HANDLING AND STORAGE

Handling
Precautions for safe handling
Keep container tightly sealed.
Store in cool, dry place in tightly closed containers.
Ensure adequate ventilation.
Information about protection against explosions and fires:
Protect against electrostatic charges.
Conditions for safe storage, including any incompatibilities
Storage
Requirements to be met by storerooms and receptacles:
Store in a cool location.
Information about storage in one common storage facility:
Store away from oxidizing agents.
Store away from halocarbons.
Do not store with interhalogens.
Further information about storage conditions:
Keep container tightly sealed.
Store in cool, dry conditions in well-sealed containers.
Specific end use(s)
No information available.


SECTION 8. EXPOSURE CONTROLS/PERSONAL PROTECTION

Additional information about design of technical systems:
Properly operating chemical fume hood designed for hazardous chemicals and having an average face velocity of at least 100 feet per minute.
Control parameters
Components with limit values that require monitoring at the workplace:
The product does not contain any relevant quantities of materials with critical values that should be monitored at the workplace.
Additional information:
No data
Exposure controls
Personal protective equipment
Follow typical general protective and industrial hygiene measures for handling chemicals.
Keep away from foodstuffs, beverages and feed.
Remove all soiled and contaminated clothing immediately.
Wash hands before breaks and at the end of work.
Avoid contact with the eyes and skin.
Breathing equipment:
Use suitable respirator when high concentrations are present.
Recommended filter device for short term use:
Use a respirator with type N95 (USA) or PE (EN 143) cartridges as a backup to engineering controls. Risk assessment should be performed to determine if air-purifying respirators are appropriate. Only use equipment tested and approved under appropriate government standards.
Protection of hands:
Impervious gloves
Inspect gloves prior to use.
Suitability of gloves should be determined both by material and quality, the latter of which may vary by manufacturer.
Material of gloves
Nitrile rubber, NBR
Penetration time of glove material (in minutes)
480
Glove thickness
0.11 mm
Eye protection:
Safety glasses


SECTION 9. PHYSICAL AND CHEMICAL PROPERTIES

Information on basic physical and chemical properties
Appearance:
Form:
Various forms (powder/flake/crystalline/beads, etc.)
Color:
Pale yellow
Odor:
Weak
Odor threshold:
No data available.
pH:
N/A.
Melting point/range:
115.21 °C (239 °F)
Boiling point/range:
444.6 °C (832 °F)
Sublimation temperature / start:
No data available.
Flash point:
> 999 °C (> 1830 °F)
Flammability (solid, gas):
Highly flammable.
Ignition temperature:
248 °C (478 °F)
Decomposition temperature:
No data available.
Auto igniting:
No data available.
Danger of explosion:
No data available.
Explosion limits:
Lower:
3.3 Vol %
Upper:
46 Vol %
Vapor pressure:
N/A.
Density at 20 °C (68 °F):
2.07 g/cm³ (17.274 lbs/gal)
Relative density
No data available.
Vapor density
N/A.
Evaporation rate
N/A.
Solubility in Water (H2O):
Insoluble
Partition coefficient (n-octanol/water):
No data available.
Viscosity:
Dynamic:
N/A.
Kinematic:
N/A.
Other information
No information available.


SECTION 10. STABILITY AND REACTIVITY

Reactivity
No data available.
Chemical stability
Stable under recommended storage conditions.
Thermal decomposition / conditions to be avoided:
Decomposition will not occur if used and stored according to specifications.
Possibility of hazardous reactions
Reacts with strong oxidizing agents
Conditions to avoid
No information available.
Incompatible materials:
Oxidizing agents
Halocarbons
Interhalogens
Hazardous decomposition products:
Sulfur oxides (SOx)
Hydrogen sulfide


SECTION 11. TOXICOLOGICAL INFORMATION

Information on toxicological effects
Acute toxicity:
The Registry of Toxic Effects of Chemical Substances (RTECS) contains acute toxicity data for components in this product.
LD/LC50 values that are relevant for classification:
Inhalative LC50 1660 mg/m3 (mam)
Skin irritation or corrosion:
Causes skin irritation.
Eye irritation or corrosion:
May cause irritation
Sensitization:
No sensitizing effects known.
Germ cell mutagenicity:
N/A
Carcinogenicity:
No classification data on carcinogenic properties of this material is available from the EPA, IARC, NTP, OSHA or ACGIH.
Reproductive toxicity:
N/A
Specific target organ system toxicity - repeated exposure:
N/A
Specific target organ system toxicity - single exposure:
N/A
Aspiration hazard:
N/A
Subacute to chronic toxicity:
N/A
Additional toxicological information:
To the best of our knowledge the acute and chronic toxicity of this substance is not fully known.
Carcinogenic categories
OSHA-Ca (Occupational Safety & Health Administration)
Substance is not listed.


SECTION 12. ECOLOGICAL INFORMATION

Toxicity
Aquatic toxicity:
No information available.
Persistence and degradability:
No information available.
Bioaccumulative potential:
No information available.
Mobility in soil:
No information available.
Additional ecological information:
General notes:
Do not allow material to be released to the environment without official permits.
Avoid transfer into the environment.
Results of PBT and vPvB assessment:
PBT:
N/A.
vPvB:
N/A.
Other adverse effects
No information available.


SECTION 13. DISPOSAL CONSIDERATIONS

Waste treatment methods
Recommendation:
Consult state, local or national regulations to ensure proper disposal.
Uncleaned packagings:
Recommendation:
Disposal must be made according to official regulations.


SECTION 14. TRANSPORT INFORMATION

UN-Number
DOT, IMDG, IATA
UN1350
UN proper shipping name
DOT
Sulfur
IMDG, IATA
SULPHUR
Transport hazard class(es)
DOT
Class
4.1 Flammable solids, self-reactive substances and solid desensitised explosives.
Label
4.1
Class
4.1 (F3) Flammable solids, self-reactive substances and solid desensitised explosives
Label4.1
IMDG, IATA
Class
4.1 Flammable solids, self-reactive substances and solid desensitised explosives.
Label
4.1
Packing group
DOT, IMDG, IATA
III
Environmental hazards:
N/A.
Special precautions for user
Warning: Flammable solids, self-reactive substances and solid desensitised explosives
EMS Number:
F-A,S-G
Transport in bulk according to Annex II of MARPOL73/78 and the IBC Code
N/A.
Transport/Additional information:
DOT
Marine Pollutant (DOT):
No
UN "Model Regulation":
UN1350, Sulfur, 4.1, III


SECTION 15. REGULATORY INFORMATION

Safety, health and environmental regulations/legislation specific for the substance or mixture
GHS label elements
The product is classified and labeled in accordance with 29 CFR 1910 (OSHA HCS)
Hazard pictograms
GHS02
GHS07
Signal word
Danger
Hazard statements
H228 Flammable solid.
H315 Causes skin irritation.
Precautionary statements
P210 Keep away from heat/sparks/open flames/hot surfaces. - No smoking.
P280 Wear protective gloves/protective clothing/eye protection/face protection.
P240 Ground/bond container and receiving equipment.
P241 Use explosion-proof electrical/ventilating/lighting/equipment.
P362 Take off contaminated clothing and wash before reuse.
P321 Specific treatment (see on this label).
National regulations
All components of this product are listed in the U.S. Environmental Protection Agency Toxic Substances Control Act Chemical substance Inventory.
All components of this product are listed on the Canadian Domestic Substances List (DSL).
SARA Section 313 (specific toxic chemical listings)
Substance is not listed.
California Proposition 65
Prop 65 - Chemicals known to cause cancer
Substance is not listed.
Prop 65 - Developmental toxicity
Substance is not listed.
Prop 65 - Developmental toxicity, female
Substance is not listed.
Prop 65 - Developmental toxicity, male
Substance is not listed.
Information about limitation of use:
For use only by technically qualified individuals.
Other regulations, limitations and prohibitive regulations
Substance of Very High Concern (SVHC) according to the REACH Regulations (EC) No. 1907/2006.
Substance is not listed.
The conditions of restrictions according to Article 67 and Annex XVII of the Regulation (EC) No 1907/2006 (REACH) for the manufacturing, placing on the market and use must be observed.
Substance is not listed.
Annex XIV of the REACH Regulations (requiring Authorisation for use)
Substance is not listed.
Chemical safety assessment:
A Chemical Safety Assessment has not been carried out.


SECTION 16. OTHER INFORMATION

Safety Data Sheet according to Regulation (EC) No. 1907/2006 (REACH). The above information is believed to be correct but does not purport to be all inclusive and shall be used only as a guide. The information in this document is based on the present state of our knowledge and is applicable to the product with regard to appropriate safety precautions. It does not represent any guarantee of the properties of the product. American Elements shall not be held liable for any damage resulting from handling or from contact with the above product. See reverse side of invoice or packing slip for additional terms and conditions of sale. COPYRIGHT 1997-2022 AMERICAN ELEMENTS. LICENSED GRANTED TO MAKE UNLIMITED PAPER COPIES FOR INTERNAL USE ONLY.

About Sulfur Nanoparticles / Nanopowder

High Purity, D50 = +10 nanometer (nm) by SEMSulfur Nanopowder, nanodots or nanoparticles are typically 10 - 45 nanometers (nm) with specific surface area (SSA) in the 30 - 50 m2/g range and also available with an average particle size of 75 - 100 nm range with a specific surface area of approximately 2 - 10 m2/g. Nano Sulfur Particles are also available in passivated and Ultra high purity and high purity and coated and dispersed forms. They are also available as a dispersion through the AE Nanofluid production group. Nanofluids are generally defined as suspended nanoparticles in solution either using surfactant or surface charge technology. Nanofluid dispersion and coating selection technical guidance is also available. Other nanostructures include nanorods, nanowhiskers, nanohorns, nanopyramids and other nanocomposites. Gold Nanoparticles and Carbon Nanoparticles have found novel application in cancer treatment using radio waves to heat and destroy a tumor, lymphoma, or metastasized cancer. Recent discoveries confirm the feasibility of this technology in humans. Surface functionalized nanoparticles allow for the particles to be preferentially adsorbed at the surface interface using chemically bound polymers.

Sulfur Nanoparticles / Nanopowder Synonyms

Sulfur nanoparticles, nanosulfur, nano-S, S NPs

Chemical Identifiers

Linear Formula S
MDL Number MFCD00085316
EC No. 231-722-6
Pubchem CID 5362487
IUPAC Name sulfur
SMILES [S]
InchI Identifier InChI=1S/S
InchI Key NINIDFKCEFEMDL-UHFFFAOYSA-N

Packaging Specifications

Typical bulk packaging includes palletized plastic 5 gallon/25 kg. pails, fiber and steel drums to 1 ton super sacks in full container (FCL) or truck load (T/L) quantities. Research and sample quantities and hygroscopic, oxidizing or other air sensitive materials may be packaged under argon or vacuum. Shipping documentation includes a Certificate of Analysis and Safety Data Sheet (SDS). Solutions are packaged in polypropylene, plastic or glass jars up to palletized 440 gallon liquid totes, and 36,000 lb. tanker trucks.

Payment Methods

American Elements accepts checks, wire transfers, ACH, most major credit and debit cards (Visa, MasterCard, AMEX, Discover) and Paypal.

For the convenience of our international customers, American Elements offers the following additional payment methods:

SOFORT bank tranfer payment for Austria, Belgium, Germany and SwitzerlandJCB cards for Japan and WorldwideBoleto Bancario for BraziliDeal payments for the Netherlands, Germany, Austria, Belgium, Italy, Poland, Spain, Switzerland, and the United KingdomGiroPay for GermanyDankort cards for DenmarkElo cards for BrazileNETS for SingaporeCartaSi for ItalyCarte-Bleue cards for FranceChina UnionPayHipercard cards for BrazilTROY cards for TurkeyBC cards for South KoreaRuPay for India

Related Elements

Sulfur

See more Sulfur products. Sulfur (or Sulphur) (atomic symbol: S, atomic number: 16) is a Block P, Group 16, Period 3 element with an atomic radius of 32.066. Sulfur Bohr ModelThe number of electrons in each of Sulfur's shells is 2, 8, 6 and its electron configuration is [Ne] 3s2 3p4. In its elemental form, sulfur has a light yellow appearance. The sulfur atom has a covalent radius of 105 pm and a Van der Waals radius of 180 pm. In nature, sulfur can be found in hot springs, meteorites, volcanoes, and as galena, gypsum, and epsom salts. Sulfur has been known since ancient times but was not accepted as an element until 1777, when Antoine Lavoisier helped to convince the scientific community that it was an element and not a compound.

Recent Research

TODAY'S TOP DISCOVERY!

November 12, 2024
Los Angeles, CA
Each business day American Elements' scientists & engineers post their choice for the most exciting materials science news of the day
CityUHK researchers discover method to reduce energy loss in metal nanostructures by altering their geometrical dimensions

CityUHK researchers discover method to reduce energy loss in metal nanostructures by altering their geometrical dimensions